Hello Guys could anyone ID this hull??(The one in my album) I don't know to add photos on the topic ! the boat has 93cm long and 33 cm wide!
hull Identification!!!
| Author | Comment | ||
|---|---|---|---|
 mariangunman |
hull Identification!!! |
Lead | |
|
Posts: 15 (02/04/09 11:47:04) |
|
||
|
HendricX |
|||
|
Posts: 52 (02/04/09 12:07:23) |
Looks like a Tornado-III or 2000 splash
|
||
|
gbeg1 |
|||
|
Posts: 94 (02/04/09 13:44:23) |
seems too small for a 15cc. Maybe typhoon? it looks like a polyester hull too
Wait for Dave, he will put us right 
Regards,
Last Edited By: gbeg1
02/04/09 13:54:15.
Edited 1 times.
|
||
|
gbeg1 |
|||
|
Posts: 95 (02/04/09 14:33:41) |
Regards,
|
||
|
mariangunman |
|||
|
Posts: 16 (02/04/09 23:29:44) |
The boat is for 3.5 cc but no idea what is it!! someone says Lightning??
ps Thanks LEON! |
||
|
Dave Marles |
boat | ||
|
Posts: 895 (02/05/09 04:43:38) |
It's a copy of a Tempest. It won't be any good but if you pay peanuts then you get monkey nuts.
Dave
Tuning software |
||
|
mariangunman |
|||
|
Posts: 17 (02/05/09 06:35:27) |
Thanks Dave !! Do you have some building instructions??Dimensions for it??
|
||
|
gbeg1 |
|||
|
Posts: 96 (02/05/09 10:40:33) |
Damn i had Tempest but edited my post.
Regards,
|
||
|
Dave Marles |
I almost won | ||
|
Posts: 896 (02/05/09 11:14:39) |
Leon, Nobody remembers second place
Building instructions are £295.00 for copied Tempests
Dave
Tuning software |
||
|
mariangunman |
|||
|
Posts: 18 (02/05/09 11:48:52) |
Ok sign me up for two!!
|
||
|
mariangunman |
|||
|
Posts: 19 (02/05/09 11:50:28) |
Whats the difference between those two??
|
||
|
Dave Marles |
|||
|
Posts: 897 (02/05/09 11:53:00) |
Lightning and Tempest were the same width. I maybe measure differently to you, but I can do that.
Dave
Tuning software |
||
|
Fredde Cederberg |
|||
|
Posts: 391 (02/06/09 12:15:36) |
Looks like a Lightning to me but Dave should know best
|
||
|
Dave Marles |
|||
|
Posts: 899 (02/06/09 17:17:40) |
Could be a Lightpest.
Dave
Tuning software |
||
|
mariangunman |
|||
|
Posts: 20 (02/07/09 23:06:07) |
I have founded the building instructions for Tempest and the overall dimensions (old gundert site )and it do not mach this hull !
|
||
|
grahame morgan |
That Boat | ||
|
Posts: 25 (02/08/09 01:55:47) |
Looks like that is one of the major draw backs to buying a copy. You never know what you have got!
Grahame |
||
|
mariangunman |
|||
|
Posts: 21 (02/08/09 04:41:47) |
Yes you are wright Grahame but this boat i got for free from a friend witch he got on Ebay with a lot of adder hulls!
|
||
|
HendricX |
|||
|
Posts: 53 (02/08/09 07:29:04) |
You can use the measures from this picture ; > L I N K
|
||
|
Teslaboats |
|||
|
Posts: 29 (02/08/09 09:34:37) |
Understandably, Dave may be a little bit reluctant to give out build instructions on a copy boat. I have built many boats without instructions and always follow this formula.
Measured from the transom: Rudder = 10% of hull length Water scoop = 15% of hull length Prop tube = 20% of hull length C of G = 37.5% of hull length
Mount the engine al low as possible and have the shaft angle as shallow as possible with the largest size prop you will use.
I am sure that most boat designers may use a similar formula for their designs as I doubt that they build a whole load of boats varying all the dimensions slightly to give you the absolute best layout. Please correct me if I am wrong here but I do not see anyone building 20-30 boats to determine this. |
||
|
gbeg1 |
|||
|
Posts: 97 (02/08/09 10:39:06) |
Teslaboats wrote: Formulas and experience to give a starting block but moving the shaft, engine or rudder is a common thing in developing the boat. My tornado 5 was the first boat that i never had to touch once first built. Regards,
|
||
|
mariangunman |
|||
|
Posts: 22 (02/16/09 01:40:41) |
So, in the end i remain wit the idea that is a TEMPEST!!!
|
||
